Search results

I have an 05 600 Renegade with the SC3 skid that has some really tired shocks. I've been bottoming out really bad and these are still the original shocks right now. Are there any aftermarket shocks out there for this year and skid? I haven't been able to find much of anything anywhere. Am I...

Has anyone removed their tail light assembly/rack and put in just an led light bar? I'm looking at doing this to open up the back end of my skid but can't find any light to use. I'm assuming with the minimal draw of the led lights that a resistor isn't needed? I'm not too electrical savvy but...

i have an 05 600 renegade with a 2"x136"x15" track and 20/43 gears. i'm planning on going to wyoming next february to ride and i'd like to take my sled if possible instead of renting. i'm wondering if taking my sled would even be worth it or if i should rent. i'd like to save a few bucks. if...

Skid went in last night and bolted to the tunnel and track tensioned. Took it for a test run and going form a 1 1/4" to a 2" is night and day. Definitely glad I went with the 2". The 20/43 gears help a lot too. This thing eats deep snow, hooks up like non-other and gets the skis off the...

Ok, so began the tear down of the skid last night to put my new track on. Everything was easy except for pulling out the drive shaft. We eventually got it but now that I'm ready to put the new track on what is the easiest way to put the drive shaft back in? We had troubles on the clutch side...

Ok, I did a lot of research on this and am 95% sure this new track will fit on my gade but it's that last 5% that I'm worried about after seeing a few other websites. Has anyone put a 2" on their gade? Was it as easy as taking the old one off and putting the new one on or are there are...

Well, I have a 2005 ski-doo renegade 600 h.o. with a 136x16x1.25 track with a 2.52 pitch on it right now. I just redid my gearing and am looking at upgrading my track. I can not for the life of me find a 136x16x1.75. I know the 1.75 will work without any modifications. Can I fit a 2" paddle...

I'm looking at buying a new electric acoustic guitar. I'm in the market to splurge on this one and spend between 1200 to 1500 bucks and was looking at getting a Martin I think but there are so many wood options, different series options, etc. that I have no clue what would be best. I know it's...

Well, this is the first major problem I've had on my sled so far. I rode saturday and had no problems whatsoever. My switch was working fine all day. Sunday rolls around and I decide to go backcountry riding so I fire up my sled, ride to my friends house and hit the kill switch when I get...

Alrighty gun enthusiasts, I need some help on this one. I recently purchased a leupold scope for my ruger m77 mark II .30-06. I also purchased leupold ruger high rings because of the 50mm size. I tried setting up my eye relief to give myself full field of view. So, I shouldered my gun to my...

I need some advice from any house builder gurus out there on an issue with a finished attic having major heat issues in the summer and cold in the winter. The house is probably 30x40 and the upstairs is a finished attack built around the 1950's. The stairway going up is open to the first...

Does anyone have clutching ideas that I could do to my sled? I don't have any clutch issues right now. I have 2500 miles on my sled. I ride half powder and half trails. I'm just curious if anyone had any good set ups. Thanks.

Alrighty, I need to throw this one out to see if anyone can help me. For some reason a light came on for the "Service Tire Monitor System". It looks like the monitors are not responding because 3 of 4 do not have pressures displayed when I go through to that menu. The warranty is up on my...

I have an 1 1/4 track on my 05 right now and was wondering if it was a possibilty to put a 1 3/4 inch track on without modifications to the drivers or having to put in a drop and roll chaincase. Thanks

Does anyone use a good cleaning product that will take the belt dust and any other dirt/grime off of your plastic panels? I just can't get those clean. Thanks