You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
Sea Doo hicup
- Thread starter fatdaddy
- Start date
cant remember why but it happens to a lot of the sea doos. man my mind is going I have helped fix them doing it to.
will let u know wend in the pm will ask my bud who owns the ski shop when I stop in tomorrow.
I am thinking stator related but like I said cant remember for sure.
will let u know wend in the pm will ask my bud who owns the ski shop when I stop in tomorrow.
I am thinking stator related but like I said cant remember for sure.
I just pulled out my 2000 sea doo jet ski and noticed it has a couple of hicups/pops at lower rpms then runs clean all the way up to 7200 rpm. any thoughts.
Is it a 800 with a water regulator on the exhaust ? Just a thought when the rubber gasket in it gets bad on my challenger it has like a hiccup at the bottom alittle , hope this helps , what motor you have?
It should be a 951 basicly the same motor as my 787 , it has a water regulator on the exhaust that commonly fails
It will prob leak alittle water if it does , I clean my power valve a couple times a year , there is also a small filter inside the carbs that cloggs real easy and it will run it lean if not cleaned or replaced
It will prob leak alittle water if it does , I clean my power valve a couple times a year , there is also a small filter inside the carbs that cloggs real easy and it will run it lean if not cleaned or replaced
zimmer1310
Member
i have an 02 GTXdi and it also has the 951cc motor. question I have is where is the VTS(trim) button on this model? the engine runs great but I would like to trim it down a little when towing the tubers. i have a start/stop, Mode and Set buttons on the left handle. thanks.
So I sould be checking a few things, how and where is the exhaust regulator, and do I simply install a new one or clean the old one. I will clean the power valves as well, now where is the filter by the carbs, I did find a filter by the front of the sea doo by taking out the front storage container, anything else i should do. do you guys have any pics of these items to share.
thanks
thanks
So I sould be checking a few things, how and where is the exhaust regulator, and do I simply install a new one or clean the old one. I will clean the power valves as well, now where is the filter by the carbs, I did find a filter by the front of the sea doo by taking out the front storage container, anything else i should do. do you guys have any pics of these items to share.
thanks
The filter is inside the carbs , about the size of a dime in diameter , the regulator id just take out on water with seat off and watch for small drips from it while running it , it looks like the power valves. But on top the muffler part of the exhaust. , there is a rubber valve inside it , with a c clamp around it , the clamp rusts off and tears the boot , if it dosent leak your fine yet, if it was me while I hard carbs off to check the filter id rebuild with all new gaskets , can get a rebuild kit for around 90 off ebay I think , it includes new filters
Bobbo,
I will check for the leaking water regulator, should the red adjuster nut be all the way in or what setting if any, I will leave it alone if no dripping occures. I assume like sleds the power valve gaskets will need to be replaced when i tear them off. do you have a good source for sea doo parts?
John
I will check for the leaking water regulator, should the red adjuster nut be all the way in or what setting if any, I will leave it alone if no dripping occures. I assume like sleds the power valve gaskets will need to be replaced when i tear them off. do you have a good source for sea doo parts?
John
Bobbo,
I will check for the leaking water regulator, should the red adjuster nut be all the way in or what setting if any, I will leave it alone if no dripping occures. I assume like sleds the power valve gaskets will need to be replaced when i tear them off. do you have a good source for sea doo parts?
John
if it isnt leaking dont touch the screw on it , otherwise all the way in and out 3 turns and adjust as needed , power valve are exactly like doing a sled .
This guy is very helpful for me in the past , this is a craigslist add , searched seadoo parts in minneapolas , he is right on lake mintonka and will have anything u need almost
I have 70+ machines parted out and are ready to ship world wide.
Nick 612 886 7300
http://minneapolis.craigslist.org/hnp/boa/3848689612.html
Seadoo Sea doo Jet ski waverunner PWC jetski